Myalarm Genesys 824 Alpha Specifikace stáhnout pdf (Strana 5)

3440-0241 Rev G

Value 0 - 9, A - D, Default: FF

52 Account Number 1 and 2 (2 Digit Entry)

When a reporting function is activated this account number

will identify the subscriber to the central station. In

memory location 52 will be the first two digits of the

account number and 52A will be the last two digits of the

first account number. 52B will be the first two digits of the

second account number and 52C will be the last two digits

Value 0000 - FFFF, Default: 0000.

Hex digits can be used in accounts numbers:

[AWAY] + 0 = A

[AWAY] + 1 = B

[AWAY] + 2 = C

[AWAY] + 3 = D

[AWAY] + 4 = E

[AWAY] + 5 = F

53 Receiver Formats for Receiver 1 and 2 (2 Digit Entry)

The first digit selects a format for Receiver number one.

The second digit selects a format for Receiver number two.

Many different types of central station receivers can accept

a multitude of formats. Naturally the format that “dumps”

the information the quickest is the most desirable. You

should consult with your central station to employ the

optimum format.

0 = SIA

1 = 10 PPS 4-1

2 = 10 PPS 4-1 extended

3 = 10 PPS 4-2

4 = 20 PPS 4-1

5 = 20 PPS 4-1 extended

6 = 20 PPS 4-2

0 - SIA

SIA is an FSK type reporting format that has all the

reporting codes encoded in the control panel software.

The reporting capabilities are simply enabled when any

reporting code other than 00 are programmed in. (A code

00 will disable the reporting capability). The information

sent is predetermined by the activation of a zone type :

EXAMPLES:

ZONE TYPE MESSAGE SENT

All Interior / Perimeter = Burglary + Zone Number

Fire zones = Fire + Zone Number

24 Hour = Burglary + Zone Number

Zone Restore (if used) = Restore + Zone Number

10 and 20 PPS formats

- The only difference between

these two formats is the speed and tone at which each

pulse of a digit in a message is transmitted. Both of these

formats will respond to 1400Hz or 2300Hz "handshake"

and "kiss off" tones. All of the 10 PPS formats are sent

using 1900Hz tones with a duration of 60 ms and a gap of

40ms for each pulse of a message digit. The 20PPS

formats are sent using 1800Hz tones with a duration of

30ms and a gap of 20ms for each pulse of a message

digit.

1 10 PPS 4-1

This format requires a four digit account number with a

single digit event code. A complete message consist of 2

identical rounds account and message digits. In the event

that you have been assigned a three digit account number,

the first digit in memory location 52 must be a zero.

Example: Account 123, program 0123.

The reporting codes in this format must be single digit,

therefore you must enter a zero in the first memory location

followed by the code number to be transmitted.

Example: code 3, program 03.

2 10 PPS 4-1 Extended

The digits are sent in the same manner as 4-1 but the

complete message consist of 2 rounds that will contain the

account number and the high digit of the message code.

This will be followed by two more rounds which will repeat

the high digit of the message code, in place of the account

number, and the low digit of the message code.

Example:

Message : 1234-F5

Transmitted : 2 rounds of 1234-F

2 rounds of FFFF-5

3 10 PPS 4-2

This is a format that is similar in reporting as 4-1 EXT.

With the exception that the reporting is sent as two

identical rounds of information.

4 - 20 PPS 4-1

All three are the same

5 - 20 PPS 4-1 Extended

as 10PPS except at a

6 - 20 PPS 4-2

faster

transmission speed.

Value 0 - 6, Default:: 1 - 1

53 A Anti-Jam Time

This is the amount of time required for the telephone company

to disconnect the phone line after the panel has hung up if it

was not "kissed" off on the first dialing attempt. Check with your

phone company for this value of time.

Value 00 - 99 seconds, Default: 15 seconds

53 B Line Type / Dial Attempts (2 Digit Entry)

The first digit indicates the telephone line type for dialing the

central station. A zero selects Rotary (pulse) dialing while any

digit 1 - 9 will select tone dialing.

Value 0 = Rotary; 1-9 = Touch-tone, Default: 0 (Rotary).

The second digit selects the number of dialing attempts to

report an event to the central station. If the communicator does

not receive a handshake and/or kissoff tone from the receiver, it

will disconnect and re-dial until the tone is heard or the

maximum number of attempts is reached.

Value 0 - 9, Default: 5. (minimum for UL 864)

53 C Delay Before Dial

(2 Digit Entry)

This function enables the capability of aborting the alarm

transmission if the panel is disarmed within the period of time

programmed in this memory location. This function is active on

burglary zones only. All 24 Hour type zones will send their data

immediately.

Value 00 - 99 seconds, Default: 00 seconds.

54 (A through G) Download Telephone Number

(Up to a 16 Digit Telephone Number)

This is a security function that when a call is initiated from a

Central Station download P.C. the panel will answer, recognize

the carrier tone from the modem, hang up the call, and call the

P.C. back. See memory location 48 for additional telephone

features

. Value 0 - D, Default: FF.

1 2 3 4 5 6 7 8 9 10 ... 21 22

Komentáře k této Příručce

Žádné komentáře

Myalarm Genesys 824 Alpha Specifikace Strana 5

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Myalarm Genesys 824 Alpha