Myalarm V-LCD1 Manuál s instrukcemi Strana 130
- Strana / 336
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
LCD PROGRAMMING - BATCH ENROLL CARDS
8-124
System 2 Installation / Programming Manual
01 03
Enter Door (0=Done) [ _ _ ]
Error!! þþþþ
Press Any Key
Enter Number þþþþ
Enter Card [00000 _ _ _ _ _]
Enter Number þþþþ
Enter Card
[________________]
The LCD will scroll the instructions:
The first line of the LCD will display the door(s) this group is allowed to access.
At the Enter Door (0=Done) [ _ _ ] prompt, enter the next door this group is allowed to
access. When you are finished press 0 and # (enter). If you wish to change the door
permission at any time, reenter the number to deny access to a specified door.
Example: If you wish to “take door #3 permission away” from these users, enter door 3 again
and the permission will be denied.
If you select Port #3 and you do not have this System set-up for networking, the LCD will
scroll:
Scrolling Options: Entry Out of Range!
To enable more than two doors, the Networking Option needs to be installed. Proceed to
Option #13 for installation instructions.
When you are finished entering door numbers press 0.
First Card Number
If you are using Wiegand or Proximity cards, check the back of the cards. There is a label
which gives you the Cards Facility Code and the five digit Card Number. Let’s say for example
your first Card has a Facility Code of 08 and a code of 12345, your First Card Number would be
812345 (the Facility Code and the Card Number), the leading zero will be ignored.
If you are using Bar Code or Magnetic Stripe cards, they do not have a facility code. Simple
enter the five digit code on the back of the card.
At this point, the LCD will scroll one of the following set of instructions:
If you chose card type 2 (Mag or Bar Code) the LCD will scroll:
Scrolling Options: 0=Quit
If you chose card type 5 (16 Digit Mag, Bar Code)
the LCD will scroll:
Scrolling Options: 0=Quit
- TABLE OF CONTENTS 3
- SECTION PAGE 3
- Programming Keypad 8
- RS232 Communications 8
- Main Relays 9
- Auxiliary Relays 9
- Voltage Outputs 9
- Request-To-Exit Inputs 9
- Zone Inputs 10
- Emergency Drop Input 10
- LED Indicators 10
- Time Keeping 10
- Electronic Serial Number Chip 11
- Memory Expansion 11
- RS485 Expansion 11
- X-10 Expansion 11
- Tamper Switch 11
- SYSTEM OVERVIEW 12
- QUICKSTART 13
- Activate Premium Options 14
- Keypad Test 15
- Card Reader Test 16
- Printer/VDT Test 17
- If There is a Problem 18
- If Everything tests OK 18
- Quick Installation 19
- VERSIONS & UPGRADES 21
- OPTIONAL EQUIPMENT 23
- Surge Protection Device 24
- INSTALLATION 27
- Earth Ground 28
- Transformer and Battery 29
- Wiring Surge Protection 31
- Keypad Styles 33
- Keypad Wire Runs 33
- Keypad Ground 33
- Keypad Connections 34
- LED Connections: 34
- Overview 35
- Status LEDS 35
- Back To Back Readers 35
- Grounding Readers 36
- Anti-Passback with Readers 36
- Bar Code Readers 37
- Data Chip Readers 39
- Data Chip Reader Wire Runs 40
- Magnetic Stripe Card Readers 41
- Proximity Readers 43
- Proximity Cards 44
- Proximity Reader Wire Runs 44
- Wiegand Readers 46
- Door Locks 48
- RTE Wiring 50
- RTE Ground 50
- Fail Safe Operation for RTE 50
- Printer Wiring 52
- Printer Ground 52
- Printer Connections 52
- Connecting To a VDT 53
- VDT Ground 54
- VDT Connections 54
- Phone Modems 55
- Short-Haul Modems 55
- Personal Computer (PC) 56
- SYSTEM OPERATION 57
- Door Functions 58
- Status of AC Power 58
- User Numbers 59
- Time Schedules 59
- User Time Schedule Example 60
- Relays & Time Schedules 61
- Automatic Door Operation 61
- Auxiliary Outputs 62
- Clearing the Keypad 62
- Keypad and Reader Operation 62
- User LED Operation 63
- Network LEDs 63
- NETWORKING 65
- RS485 Wiring 66
- Network Setup 66
- Buffer Size 67
- Response Time 68
- Programming Considerations 68
- Trouble Shooting 69
- Testing Additional Units 70
- PROGRAMMING USING THE LCD 71
- Required Events 74
- User Names 74
- Networking 75
- Memory Error 75
- 1=Yes, 2=No 79
- Enable DST? [ 2 ] 79
- Time Schedule Example 81
- Choosing the Schedule 82
- Choosing the Time Cell 82
- Day-of-Week or Holiday Date 83
- Holiday Date 83
- Changing a Cell 84
- Trigger Time 84
- Trigger State 85
- 1=Program Ports þþþþ 87
- Select Option [ _ ] 87
- Selecting the Port to Program 88
- Selecting the Input Device(s) 88
- Relay Type 89
- Automatic Port Operation 90
- Selecting Any Card/Chip Mode 91
- Selecting the Output 92
- Output Mode 92
- Momentary Time 93
- Trigger Event 93
- Automatic Output Operation 95
- User Codes 100
- Additional Outputs 101
- Door Schedules 102
- Anti-Passback 103
- User Type 103
- Enrolling Cards 104
- Door Number 105
- User Cards 106
- Memory Full 109
- Users Enrolled 0001 þþþþ 110
- Want to Continue? [ 1 ] 110
- Enrolling Data Chips 111
- User Chips 114
- Duplicate Code! 114
- Bad Code! 118
- (Option #9) 119
- Batch Enrolling Keypad Codes 120
- Seed Number 123
- Code Type 126
- System Status 128
- User Number 128
- Number of Users 129
- First Card Number 130
- Batch Enrolling Data Chips 136
- Delete Users (Option #10) 144
- Delete More? 145
- Reports (Option #11) 146
- Choosing the Output Device 147
- User Report in Network Mode 149
- Choosing the User Report 149
- User Door Permission 149
- User Schedules 150
- Temporary Users 152
- Delete the Events? 153
- Configuration 155
- Schedule 156
- Choosing Your Output Device 156
- Current Secret # 159
- Bad Secret #! 159
- New Secret # 159
- Re-enter New Secret # 159
- Install Options (Option #13) 160
- Enter the Upgrade Key 161
- Unit Number 162
- Port Number 162
- On / Off 163
- Override Outputs 164
- Output Number 164
- Baud Rates (Option #15) 165
- Clear Users (Option #16) 166
- Clear Memory (Option #17) 166
- Network Options (Option #18) 167
- Slave Number 168
- Reload Slave? 168
- Slave Unit 168
- RS485 Test 169
- Backup-Restore (Option #19) 170
- PROGRAMMING USING A VDT/PC 173
- Accessing the System 174
- Power-up Messages 175
- Entering Program Mode 178
- Main Menu 179
- Time and Date (Option #1) 180
- 1=Yes,2=No 181
- Enable DST? [2] 181
- Select Card Type (Option #4) 188
- Anti-Passback (Option #7) 198
- Enrolling Keypad Codes 199
- Option Not Active 229
- Install in Option 13 229
- Press Any Key 229
- PC/VDT PROGRAMMING - REPORTS 247
- Door Ajar 07:06:01 04/05/97 248
- Door Closed 07:22:40 04/05/97 248
- To Start/Stop Print 249
- Waiting 249
- WINDOWS PROGRAMMING & 265
- MODEM SETUP 265
- Windows 3.1 266
- INSTALLING AN EPROM OR RAM 269
- EPROM & RAM CHIPS 270
- TROUBLESHOOTING 271
- FREQUENTLY ASKED QUESTIONS 275
- AVAILABLE USERS CHART 279
- LCD MESSAGES 281
- TERMINAL DESCRIPTIONS 283
- GLOSSARY 287
- WIRING DIAGRAMS 293
- CAUTION!!! 294
- 48CHARACTER 297
- LIQUIDCRYSTALDISPLAY 297
- Figure4-TerminalDescriptions 298
- Figure5-TestPoints 299
- 8CONDUCTOR22AWG 300
- SHIELDEDCABLE 300
- Figure8-BatteryandTransformer 302
- Figure9-PrinterConnection 303
- 9PINMALE 304
- CONNECTOR 304
- FAILSAFECONTACTS 309
- SEEFAILSAFEDIAGRAM 309
- KERIPROXIMITYREADER 312
- 2CONDUCTOR22AWG 323
- Figure32-EmergencyDropInput 326
- 22GAUGESHIELDEDTWISTEDPAIR 328
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Myalarm V-LCD1
(22 stránky)
(362 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce